Taking Away Asphalt Silo Gate Pains With FLO Automatic Greasing Systems

Jan 29, 2021 - 5 years ago

Mississauga-based greasing solutions expert, FLO Components Ltd. is currently working with several Asphalt companies to install Automatic Lubrication Systems (ALS) on their asphalt storage silos.
FLO’s Marketing Specialist, Gabriel Lopez explains; “At an asphalt plant, a truck drives underneath the silo and the asphalt is dropped into the truck body, which is then trucked to where the Paving crew is laying down the asphalt. The silo has a door or “gate” at the bottom, which has to be able to open and close repeatedly as the Plant fills the trucks. The hinges or bearings on these gates must be properly lubricated, because a stuck gate can be catastrophic.”
“If it gets stuck closed, you have a truck underneath that cannot get material to transport over to the asphalt crew and everything stops. Even worse, if the gate gets stuck open, it will empty the entire silo of very hot asphalt into the truck (overfilling), onto the ground and typically even onto the scale. The truck has likely pulled away. Hopefully nobody has gotten hurt, but you are left with a lot of clean-up and potential environmental and safety issues, and again, all paving stops.”
There are serious costs and major downtime associated with a stuck silo gate. “If it’s happened to you, you’ve felt that pain.” According to Lopez, the costs incurred if a piece of paving equipment breaks down on the job and forcing the crew laying down the asphalt to stop production, is over $2,500 per minute. A stuck gate would similarly shut down that lay down crew, incurring the same costs or more if repairs and clean-up are required.
Currently on many silos, the points needing grease are “remote-lined” out to the side of the gate according to Lopez. However, “It’s not just a case of walking up to a grease point and hooking up a grease gun”, he says. Trucks have to be able to get underneath the gate, so these points are typically 20’ in the air - a man lift, ladder or something else to elevate the worker is required to grease those points. This leads to potential safety risks, use of harnesses and other safety measures and rental of man lifts. Furthermore, greasing through remote lines can’t be done during production, so it’s either before or after, potentially causing worker overtime.
FLO’s solution is to use an Automatic Lubrication System to lubricate the four main points of the gate. The ALS is a self-contained grease lubrication system that typically gets mounted on one of the support structures or I-beams of the silo. It is a fully monitored system, with a grease reservoir and 120V pump at ground level, a single supply line running up to a distribution valve mounted underneath the silo, and heat-resistant feed lines running to the bearing points. Operation of the ALS is tied into the start of production and is programmed to run on timed (adjustable) intervals. The pump comes on periodically and a small measured amount of grease is sent into the individual bearing points, while the silo is operating. This is one of the biggest advantages of ALS, Lopez says; “Because the bearing is turning when it receives the grease, you get much better coverage and far better protection”.
“The Silo Lube System helps eliminate the stuck gate scenario and all the drawbacks of using remote grease lines, and additionally gives you all the standard benefits of an Autoluber – less downtime, increased productivity, improved worker and environmental safety, etc. It’s just another way FLO, as the saying here goes, is ‘helping to take away our customers’ pain’.”

About FLO Components
FLO Components Ltd. is an automatic greasing systems specialist and the leading supplier of "Total Lube Solutions" to major manufacturers and truck and heavy equipment users in Ontario and Manitoba. Established in 1977, FLO uses application expertise and qualified service technicians to provide cost effective Solutions for all types of lubrication and fluid handling applications and help clients reduce unscheduled downtime and improve productivity. FLO Components' Solutions include: systems design, auto lube systems, hammer lube systems, general lube equipment, specialty lubes, onsite service & installation, lube audits, lubrication training, scheduled on-site maintenance programs, and a factory authorized warranty & service facility. For more information on FLO’s products or services, please contact the Customer Service Department TOLL free at (800) 668-5458, e-mail [email protected] or visit online at www.flocomponents.com.
Source: FLO Components